Flood Free Switch FF-98-II
-
Model Number:
FF-98 Floodfree
-
Product Name:Flood Free Switch FF-98-II
-
Manufacturer:
-
Series (4 Models):
Sump Pump Switch
Model Number
FF-98 Floodfree
PumpBiz FF-98 Floodfree
Flood Free Electronic Sump Pump Float switch Control and Alarm in one small state-of-the-art electronic package called FLOODFREE. Alternate see USC3 switch. Never Flood Again!
Just plug any pump's power cord into Floodfree outlet and get the most dependable and advanced electronic pump operation and high water level alarm available. Unit plugs into standard household outlet. Universal replacement of all types of sump pump water level controls. Upgrade manual pumps to automatic. Use as a alarm in critical areas. The IntelliShield control uses patented electronic surface transfer (EST) to detect the presence of water. A tiny, short duration, electrical charge is placed into liquid touching the probes surface. Next the stored charge is removed and measured with a current sensor. Peak of the removed charge depends on the surface area (mm2) of contact between the probe and liquid. Air or resistance cannot store a charge and do not produce a signal. Thereby EST ignores resistive residues like rust or salts that stick to the probe and eventually connect it to ground. Thin sticky films like soap suds or toilet paper that can bridge the rods are ignored by requiring a large liquid to probe contact area. EST is set to trip when liquid makes contact with the high rod. Patent Pending Z-cross technology closes the relay contact at zero volts and opens it at zero current. Its intelli pump shield provides smoother start-ups , extending pump motor and relay contact life. Rated for a million + cycles.
While the pump is running, the water level should drop. If it does not drop below the high rod within 15-seconds the alarm sounds. Sounding a warning well before flooding can occur. The pump continues to run until the liquid level falls below the tip of the low rod.
Three prong plug, 110v, 20 amp rating. Patent Pending pulse technology prevents oil fouling.
Elevator Sump Pump Controls and pumps benefit from the switches simple but effective technology. Also can be used in transformer containment barriers, underground vaults, anywhere you need to pump water and not oil in commercial applications. See the water, leave the oil.
Use to keep your Basement Dry. Popular pumps to use with the FloodFree MIC FF-98-II is the 505000, 505025.
- Can be tied into home alarm or phone dialer system for remote notification
- Can be used to turn off a pump and prevent dry running
- Loud 80 dB Audible Alarm & Light for high level condition
- Corrosion-proof sensor probes are Stainless
- 10 FT long sensor wire probe is INCLUDED
- 15 amp contact rating
- Works with any water
- No tools required
- No floats to get stuck
- Plug-and-Play (Dim's 4x1.5x2.25")
- Sensing probe with fixed on/off pumping cycle. Pumping range is 5.5” same as a standard float cycle. The pumping range can be made shorter.
- or longer. The top (short) probe needs to get wet to start the pumping cycle.
FloodFree is not affected by pump movement, water turbulence or foreign material that inhibit float control operation. FloodFree has 100,000 operating cycles rated at 20 amps compared to float or diaphragm switches with only 10,000 operating cycles rated at 15 amps. B004X6AJ9E Replaces Simer Pump sss-11 electronic probe or use instead of the Intelli pump. Also see the Sump Watcher electronic float switch.
Model Number | FF-98 Floodfree |
---|---|
Series | Flood Free Electronic Level Control Pumps |
Voltage (V) | 115 |
Voltage (Range) | 110-120 |
Phase (Ø) | Single (1) |
Motor Frequency | 60 |
Self Priming | Yes |
Mechanical Seal | No |
Other | Voltage 100-130VAC. Wire can be shortened or lengthened as needed. Floodfree can replace your existing float, no need to change out the pump. The pumps rarely go bad, so all you need to do is remove the float or tie the float in the "on" position. Sensor can be extended to any length. The patent pending Z-Snap technology for the pump relay provides one million operations. ZSnap closes the relay contacts at zero volts on the same positive cycle each start and opens the contacts at near zero current. This results in preventing pump starts at peak voltage or temporary reverse cycle starts. Thus providing stronger/smoother starts and extending the pumps parts such as the bearing, capacitors, seals, and motor. The alarm warns you before flooding occurs locally with an 80 db audible alarm or can be hook up to a dialer or security system for remote warning. |
Approvals | CSA, ETL |
Drain | Yes |
Port Rotation | Yes |
Country of Manufacture | United States |
Weight (Lbs) | 3.000000 |
Warranty (YRS.) | 1 |