Horizontal Pumps
Designed and meant to be used as a horizontally mounted assembly.
This includes feet on the pump, motor or both for securing the pump
and motor to its floor or structure. The most common type of
Horizontal pump is the End Suction, where the fluid enters the
front end of the casing and exits perpendicularly. The source of
liquid is either above the pump, in which case it is a positive
head and no special priming is needed. If the liquid source is
below the pump then either a priming chamber is needed or use of
some sort of suction side valve, i.e. foot valve, to maintain prime
in an open pumping system. If the inlet and outlet go into the same
tank, i.e. re-circulating or filtering, and the lines are kept
below the surface level, then after initial priming the system will
maintain its prime.The two big considerations that must be given to
horizontal pumps is priming method and NPSHa.Typical Centrifugal
Horizontal pumps include mechanically sealed, magnetic coupled
seal-less, self-priming, multistage, jet, back pullout, portable,
API and ANSI to name a few.
-
Finish Thompson Pumps (FTI)
ULTRAchem ANSI DIM. Mag Drive pump w/ 3hp motor
UC1516AECCSVF4121409
$8,100.00Tefzel lined ANSI / ANSI B73.1 Casing dimensional Magnetic coupled process pump. Sealless. Powerful neodymium magnets, no seals to replace. The modified concentric volute equalizes pressure across the entire flow range allowing minimal hydrauli... -
MP Pumps
FM5 pump pak Engine mount
21300
$1,340.00Flomax Pumps 5 are self-priming pumps, pipe size 1.5" NPT. Pump end for use with standard engines. For use with 3/4" crankshaft. PumpPackPump kit, Aluminum Learn More -
MP Pumps
FM5 Pump w/ no engine
21301
$2,830.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Pump end for use with standard engines. For use with pump engine. BronzeBronze, Engine mount kit Learn More -
MP Pumps
FM5 Pump w/ no engine
21306
$880.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Pump end for use with standard engines. For use with PUMPAK with Base and Fasteners. -
MP Pumps
FM5 Pump w/ 2HP Motor
26300
$1,850.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Electric Motor Driven Pump using a Close-Coupled Cast Iron Electric Motor-2 HP2HP 230/460v Learn More -
MP Pumps
FM5 Pump w/ 3HP
26301
$1,720.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Electric Motor Driven Pump using a Close-Coupled Cast Iron Electric Motor-3 HP -
MP Pumps
FM5 Pump w/ 1.5HP
26549
$1,760.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Electric Motor Driven Pump using a Close-Coupled Cast Iron Electric Motor-1.5 HP. FLOMAX® 5 self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights...
1.5HP 115/230v CI Learn More -
MP Pumps
FM5 Pump w/2HP Motor
26550
$2,070.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Electric Motor Driven Pump using a Close-Coupled Cast Iron Electric Motor-2 HP2HP 115/230v CI Learn More -
MP Pumps
FM5 Pump
31244
$2,130.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Electric Motor Driven Pump using a Close-Coupled Cast Iron Electric Motor-3 HP3HP 230/1 Learn More -
MP Pumps
Series 80 w/ motor
26535
$1,710.00Series 80 End Suction Centrifugal Pump. 1.5" NPT suction and 1.25" NPT vertical or horizontal discharge. Close-coupled Cast Iron Electric Motor-1.5 HP, 3-phase, 230/460 V, 3450 RPM. Pumps are right hand rotation with bronze enclosed impeller.