Horizontal Pumps
Designed and meant to be used as a horizontally mounted assembly.
This includes feet on the pump, motor or both for securing the pump
and motor to its floor or structure. The most common type of
Horizontal pump is the End Suction, where the fluid enters the
front end of the casing and exits perpendicularly. The source of
liquid is either above the pump, in which case it is a positive
head and no special priming is needed. If the liquid source is
below the pump then either a priming chamber is needed or use of
some sort of suction side valve, i.e. foot valve, to maintain prime
in an open pumping system. If the inlet and outlet go into the same
tank, i.e. re-circulating or filtering, and the lines are kept
below the surface level, then after initial priming the system will
maintain its prime.The two big considerations that must be given to
horizontal pumps is priming method and NPSHa.Typical Centrifugal
Horizontal pumps include mechanically sealed, magnetic coupled
seal-less, self-priming, multistage, jet, back pullout, portable,
API and ANSI to name a few.
-
Riverside
3.5 HP Briggs & Stratton Gas powered Centrifugal Pump
S2B
$1,059.00Centrifugal pumps are used where maximum head, fast priming, and a combination of high volume and pressure are required. Centrifugal pumps can handle small quantities of solids, up to 10% by volume. The S2B and S2H feature a sand cast aluminum hou...2" Learn More -
Riverside
5.5 HP Honda GX 160 Gas powered Centrifugal Pump
S2H
$1,289.00Centrifugal pumps are used where maximum head, fast priming, and a combination of high volume and pressure are required. Centrifugal pumps can handle small quantities of solids, up to 10% by volume.The S2B and S2H feature a sand cast aluminum hous...
2" Honda Engine Learn More -
MP Pumps
Flomax 8 Pedestal pump
21339
$1,275.00Flomax 8 pumps are self-priming pumps, pipe size 2" NPT. CI pump mounted to a CI bearing pedestal which has a 3/4" diameter shaft. Right hand rotation.Pedestal mounted CI 5" imp. Learn More -
MP Pumps
Flomax 8 Pedestal pump
21336
$1,925.00Aluminum Flomax 8 pumps are self-priming pumps, pipe size 2" NPT. Aluminum pump mounted to a CI bearing pedestal which has a 3/4" diameter shaft. Right hand rotation. 21330 is another version.The FLOMAXï½® series of pumps are commonly used in...
Aluminum Pedestal mnt Learn More -
Koshin Pumps
Koshin Dewatering Pump 2 inch Robin
SE-50EX
$1,628.10Koshin Dewatering Pump with Robin Subaru engine Water Pump 2 inch. All aluminum die cast pump housing, with CI impeller and volute for lightweight and portability. Metal Carry handle and base. Robin EX13 4-cycle engine so NO mixing gas. Use sta...Robin Subaru 4-Cycle 4.3HP 9480GPH Learn More -
Berkeley Pumps
B1-1/2ZPH (15HP - Three Phase - CI)
B53759
$9,695.00Berkeley Pumps offers a variety of models with the pump attached directly to the motor frame.- All pumps offer back pull-out design
- Impeller size is 9"
- Berkeley Pump discharge size: 1-1/2"
- Berkeley Pump suction size: 2"
15HP 230/460v packed Learn More -
Pedrollo Pumps
Centrifugal End Suction pump
CPH50C16S High Head
$4,010.09High pressure centrifugal water pump with electric motor. Good for wash down, irrigation, booster, chiller. Pedrollo centrifugal pump for clean water . They are recommended for pumping clean water and liquids that are chemically non aggressive ...5HP 230v/1 Learn More -
Koshin Pumps
Plastic Engine drive pump
PGH-50
$832.50Plastic Engine drive pump
for dewatering, chemical transfer, Ag pesticides, seawater. Self Priming. Honda GX120 gas engine with low oil alert. Pump materials make it good for pumping DEF diesel exhaust fluid urea, and many common AG chemicals.
P...
Honda 4HP 8876 GPH Learn More -
Berkeley Pumps
B1-1/2ZPLS
B54504
$8,002.00Berkeley Pumps offers a variety of models with the pump attached directly to the motor frame.- All pumps offer back pull-out design
- American Made
- Berkeley Pump discharge size: 1-1/2"
- Berkeley Pump suction size: 2"
15HP 230/460v Seal Learn More -
Pacer Pumps
Centrifugal Pump
SE2HL-C3.0C
$2,007.90Pacer S pump 58-12H4 C3.0C close coupled to a TEFC 3hp motor.
Self priming FRP plastic resists abrasive particles, good for most water transfer applications. Widely used to transfer and spray de-icing / anti-icing solutions, such as calcium chlor...
3HP 230v/1 Learn More
