Gas Rubber Impeller Pump
-
Manufacturer:
-
Series (5 Models):
-
Product Name:Gas Rubber Impeller Pump
-
Model Number:405MG-03UGY
Oberdorfer 405MG-03UGY
Gas Engine Oberdorfer rubber (flex) impeller pump with solid cast bronze housing. Close coupled Rubber Impeller Pumps are made of high quality bronze for maximum corrosion resistance. The rubber impeller is mounted on a separate stainless steel shaft which is counter-bored on the outer end in order to slide over the carbon steel motor shaft. Ball or sleeve bearings in the motor or engine support the shaft. Model 405M has a mechanical seal. Impellers are made of Neoprene rubber, Buna N impellers are available on request. (405M-07)
Flexible blades on the periphery of the impeller provide the pumping action. While the impeller rotates, the liquid between the blades is continuously squeezed out into the discharge port by a cam located inside the pumping chamber. The flow may be throttled or shut off for a short period without the need of a relief valve.
Portable gasoline engine drive
LIQUIDS AND TEMPERATURE:
Liquids handled by Rubber Impeller Pumps with standard Neoprene impellers are primarily fresh or salt water and water solutions. Rubber Impeller Pumps are not suitable for pumping gasoline or solvents. Buna N (405M-07) impellers can handle oil contaminated water and kerosene at reduced impeller service life. Liquid temperature range is from 40o F to 140oF. If freezing conditions are expected, the pump should be drained by loosening the cover screws and the pump chamber should be filled with methyl alcohol based antifreeze. Viscous liquids and oils can not be pumped with Rubber Impeller Pumps.
This model does NOT have the optional vacuum switch. Do not run dry. Self priming after being "wet".
Model Number | 405MG-03UGY |
---|---|
part number | 405MG-03UGY |
Series | Sewage Transfer Macerator |
Max Flow (GPM.) | 30 |
Max Flow GPH | 1800 |
TDH Maximum (Ft) | 40 |
TDH Maximum (PSI) | 18 |
Horse Power (HP) | 3 |
Horsepower (IE .5, 1, 1.5, 20) | 3 |
Inlet Connection Type | FNPT |
Inlet (In.) | 1 |
Outlet Connection Type | FNPT |
Outlet (In.) | 1 |
Wetted Materials | 304SS, Bronze |
Elastomers / O-ring | Neoprene |
Motor | Gas Engine |
Speed (RPM.) | 3600 |
Self Priming | Yes |
Max Operating Temperature (F) | 140 |
Max Particle Size (In) | 1.0000 |
Viscosity | Glycerine 880.00 cp 5000.00 ssu |
Shaft | 304SS |
Mechanical Seal Face | Carbon-ceramic |
Mechanical Seal Type | Single |
Coupling | Y |
Other | On initial start-up, pump must be primed to prevent dry-running of the impeller. Liquids handled by Rubber Impeller Pumps with standard Neoprene impellers are primarily fresh or salt water and water solutions. Rubber Impeller Pumps are not suitable for pumping gasoline or solvents. Nitrile (405M-07)impellers can handle oil-contaminated water and kerosene at reduced impeller service life. Liquid temperature range is from 40o F to 180oF. If freezing conditions are expected, the pump should be drained by loosening the cover screws and the pump chamber should be filled with methyl alcohol based antifreeze. Viscous liquids and oils cannot be pumped with Rubber Impeller Pumps. |
Drain | No |
Port Rotation | Yes |
Country of Manufacture | United States |
Weight (Lbs) | 39.000000 |
Warranty (YRS.) | 1 |
GPM Of Water At 20 Feet Of Head | 24 |
GPM Of Water At 40 Feet Of Head | 22 |