Drum pump - SS-39 & air motor- SP-A2
-
Model Number:
A2 SS-39
-
Product Name:Drum pump - SS-39 & air motor- SP-A2
-
Manufacturer:
-
Series (61 Models):
Hazardous Location
Model Number
A2 SS-39
$2,438.80
Standard A2 SS-39
Hazardous Location Drum Pump, Air motor
Stainless steel pump and Air / pneumatic motor is inherantly Explosion Proof. Motor and Pump Combination. Drum Pump Motor: High volume compressed air motor, operating pressure = 92 psi ( 6.32 bar) @ 28 cfm, includes muffler, inlet = 3/8" 9.5 mm). Drum Pump, High Volume. SS316 construction, TFE guide sleeve, 39" ( 1000 mm) immersion. In applications where electricity is unavailable or dangerous, use these pumps with a nonsparking air-powered motor. They have an NPT female air connection. Total weight 15 lbs.
Same as 8252K12 and 2824K39.
Acetone, Diesel Fuel, Ethanol, Gasoline, Hydraulic Oil, Isopropyl Alcohol, Kerosene, Lacquer Thinner, Methanol, Methyl Ethyl Ketone, Mineral Spirits, Motor Oil, Nitric Acid (20%), Paint, Phosphoric Acid, Xylene. With a length on 1" hose and the result flow restriction practicle flow rate will reduce to approximately 35gpm. Maximum flow is achieved by using a 1-1/4" hose or larger. Use for ethyl alcohol, isopropyl alcohol and sanitizer solutions for cleaning.
Air motor air presure can be varied between 44-87 psi
WARNING: Pumping of flammables or combustible liquids can generate a static electric discharge, causing fire or explosion resulting in injury or death. Read and understand operating instructions before starting this unit. Follow all federal, state and local safety codes including NFPA 30 - NFPA77. Prior to connecting to air supply, install bond and ground wires and check continuity of each wire. A meter reading of one ohm or less is required for safe liquid transfer. Use only metallic drum, receiving vessel and metallic pump (SP-SS) when pumping flammables.
| Model Number | A2 SS-39 |
|---|---|
| Series | Drum Pump & Motor 32gpm |
| Max Flow (GPM.) | 53 |
| Max Flow GPH | 3180 |
| TDH Maximum (Ft) | 36 |
| TDH Maximum (PSI) | 15 |
| Horse Power (HP) | 3/4 |
| Horsepower (IE .5, 1, 1.5, 20) | 0.7500 |
| Watts | 560.000000 |
| Outlet Connection Type | Barb |
| Outlet (In.) | 1 |
| Wetted Materials | 316SS, Teflon |
| Elastomers / O-ring | Teflon-PTFE |
| Motor | Air-Pneumatic |
| Speed (RPM.) | variable |
| Self Priming | ---- |
| Max Operating Temperature (F) | 80 |
| Viscosity | Glycerine 880.00 cp 5000.00 ssu |
| Shaft | 316SS |
| Length (In.) | 39.000000 |
| Mechanical Seal | No |
| Mechanical Seal Type | Single |
| Coupling | Y |
| Other | Engineered for use with flammable liquids or in hazardous environments. Uses air pressure 44 to 87psi and 32CFM. Hazardous Location for Flammable Liquids?These pumps are rated for Zone 0 hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits. Pumps have an aluminum housing, and they include bonding and grounding wires and a hanger. Discharge connection is barbed and fits a 1? ID tube (not included). Bung adapters available. |
| Approvals | CARB, ETL, SSPMA |
| Pump Bearing | Rulon |
| Low Oil Shutdown | Yes |
| Impeller Material | plastic |
| Duty | Continouos |
| Drain | Yes |
| Port Rotation | Yes |
| Weight (Lbs) | 15.000000 |
| Warranty (YRS.) | 3 |
>
