Horizontal Pumps
Designed and meant to be used as a horizontally mounted assembly.
This includes feet on the pump, motor or both for securing the pump
and motor to its floor or structure. The most common type of
Horizontal pump is the End Suction, where the fluid enters the
front end of the casing and exits perpendicularly. The source of
liquid is either above the pump, in which case it is a positive
head and no special priming is needed. If the liquid source is
below the pump then either a priming chamber is needed or use of
some sort of suction side valve, i.e. foot valve, to maintain prime
in an open pumping system. If the inlet and outlet go into the same
tank, i.e. re-circulating or filtering, and the lines are kept
below the surface level, then after initial priming the system will
maintain its prime.The two big considerations that must be given to
horizontal pumps is priming method and NPSHa.Typical Centrifugal
Horizontal pumps include mechanically sealed, magnetic coupled
seal-less, self-priming, multistage, jet, back pullout, portable,
API and ANSI to name a few.
-
MP Pumps
Bronze Circulator pump
28781
$2,275.00- FEATURES
- Direction of discharge can be at any angle
- Series Wound, Super duty, Brushless and permanent magnetic motors available
- brush life up to 10,000 hours
- Hard Face Mechanical Seal
- Nickel steel impeller
- OPTIONS
- Companion Flanges Availab...
-
MP Pumps
Centrifugal pump pedestal mounted
26643
$1,975.00Series 120 high capacity centrifugal pumps are close coupled to standard NEMA "C" face motors, Pedestal mounted or in kits for motor and gas engines. Adaptor protects the motor. Available in cast iron, or bronze construction to suit a wide variet...
-
MP Pumps
High Head Pedestal pump
36647
$2,995.75High Head Pedestal CI pump.
Self priming high head centrifugal pump, pedestal mounted for pulley or belt drive on ship or boat.
- 1 1/2 x 1 1/2" HIGH HEAD
- ABS type approved for many shipboard services
- FLOWS - TO 140 GPM
- PRESSURES - TO 190 TDH...
hhlf Learn More -
MP Pumps
High Head pump Pumpak HHLF
36085
$2,430.68Self priming high head centrifugal pump, for close coupled to an electric motor supplied seperately.
- 1 1/2 x 1 1/2" HIGH HEAD
- For “C” FACE ELECTRIC MOTOR DRIVE 184TC
- FLOWS - TO 140 GPM
- PRESSURES - TO 190 TDH
- CAST IRON CONSTRUCTION
- DRI...
Electric motor pump kit Learn More -
MP Pumps
Series 80 pump pak
26038
$1,450.00Series 80 End Suction Centrifugal Pump. 1.5" NPT suction and 1.25" NPT vertical or horizontal discharge. Pump kit NO motor. For 145TC -
Berkeley Pumps
B1-1/2ZPL (7.5HP - Three Phase - CI)
B53751
$6,818.00Berkeley Pumps offers a variety of models with the pump attached directly to the motor frame.- All pumps offer back pull-out design
- Impeller size is trimmed to 7.18"
- Berkeley Pump discharge size: 1.5"
- Berkeley Pump suction size: 2"
7.5hp 230/460v packed Learn More -
Berkeley Pumps
B1-1/2ZPL (10HP - Single Phase - CI)
B55574
$9,330.00Berkeley B1-1/2ZPL B55574 water pump 10HP
Berkeley Pumps offers a variety of models with the pump attached directly to the motor frame. Often used for irrigation.
- All pumps offer back pull-out design
- Impeller size is 9""
- Cast Iron impeller ...
10HP 230/1 Packing Learn More -
Berkeley Pumps
B1-1/2ZPL (10HP - Three Phase - CI)
B53752
$7,623.00Berkeley Pumps offers a variety of models with the pump attached directly to the motor frame.- All centrifugal pumps offer back pull-out design
- Impeller size is trimmed
- Berkeley Pump discharge size: 1.5"
- Berkeley Pump suction size: 2"
10HP 230/460V ODP PACKING Learn More -
Berkeley Pumps
B1-1/2ZPL (15HP - Three Phase - CI)
B53753
$8,275.00Berkeley Pumps offers a variety of models with the pump attached directly to the motor frame.- All pumps offer back pull-out design
- Impeller size is 9"
- Berkeley Pump discharge size: 1-1/2"
- Berkeley Pump suction size: 2"
15HP 230/460v PACKING Learn More -
MP Pumps
FM5 Pump end only
26082
$3,925.00Flomax 5 are self-priming pumps, pipe size 1.5" NPT. Pump end for use with standard 56C motor. NOT For use with gas engine. Bronze
