My Cart

N9000 Pedestal Bronze Rotary Gear Pumps

Oberdorfer Pedestal Bronze Rotary Gear Pump. Often used as an oil pump on large ships to pre-lube the bearings, honey production systems. Pump flow is reversible.
  • Bronze Corrosion Resistant Castings
  • Model #'s with E have BSPT
  • Special Cast Bronze Gears
  • Stainless Steel Shafts & Fasteners
  • Formed Ring Seal Packing (Lip & Mechanical Seals on Special Order)
  • Heavy Duty Carbon Bearings (Self Lubricating) Carbon or Bronze (model #'s with L have bronze bearings)
  • Positive Displacement Flow
  • Pumps with relief valve have a R in the model number

Drive: Either direct drive with flexible coupling or pulley drive can be used. Make sure both flexible coupling halves are properly aligned. When using a pulley, do not overtighten the belt. Also, to absorb belt side thrust at higher pressures and larger size pumps, an external ball bearing support is recommended.

Suction Lift: Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet. Though gear pumps are self priming, a foot valve is recommended. If possible, wet the gears with liquid to be pumped for the first dry start. Liquid retained in the system and gear chambers serves to “wet†the pump on subsequent starts.

Liquids and Temperature: Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. These positive displacement pumps have tight tolerances. Fine abrasives like sand, silt, or powders in suspension will accelerate pump wear and reduce throughput. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified (see chemical compatibility or check factory). When possible, flush the pump after each usage. Temperature extremes are detrimental to service life and should be avoided. Basic metals of construction allow a temperature range of -40 to 400F. Some lip and mechanical seal elastomers have a limit of 212oF. (see engineering data or check factory). Allowing a liquid to freeze in the pump can cause damage.

By-Pass and Rotation: The pump by-pass is not intended to be a metering or flow control device. Its main purpose is to function as a pressure relief when the desired set point is exceeded, overheating can occur within 5 -10 minutes if the discharge line is completely shut off for extended periods. Reversing rotation reverses the “IN†and “OUT†ports and the location of the by-pass ports have to be reversed. The by-pass valve is factory set at 50 p.s.i. To increase the setpoint, turn the by-pass valve adjusting screw in a clockwise direction. Pumps with relief valve have a R in the model #.

Relief valve factory set at 50 PSI. Pump is bi-rotational or reversible. Reversing the rotation reverses the In Outlet ports and the location of the by-pass port has to be reversed.
Shop By
Shopping Options
inlet size
  1. Less than 1" 4 items
  2. 1" 25 items
PRICE $
$  -  $
View as List Grid

Items 21-30 of 31

Set Descending Direction
per page
  1. Oberdorfer Pumps

    Bronze Pedestal Gear Pump w/ relief valve

    N7000R

    $1,044.00
    Bronze Pedestal Gear pump with relief valve. Often used as a oil pump on large ships to pre-lube the bearings. Pump flow is reversible.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid...
    3/4" Packed Learn More
  2. Oberdorfer Pumps

    Bronze Pedestal Gear Pump

    N9000S15

    $711.00
    Bronze Pedestal Gear pump. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the backpressure in the...
  3. Oberdorfer Pumps

    Bronze Pedestal Gear Pump

    N9000S16

    $841.00
    Bronze Pedestal Gear pump. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the backpressure in the...
  4. Oberdorfer Pumps

    Bronze Pedestal Gear Pump

    N9000S17

    $965.00
    Bronze Pedestal Gear pump. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the backpressure in the...
  5. Oberdorfer Pumps

    Bronze Pedestal Gear Pump

    N4000L

    $599.00
    Bronze Pedestal Gear pump. Often used as a oil pump on large ships to pre-lube the bearings. See performance chart for motor speed VS HP VS performance.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite a...
    1/2" Learn More
  6. Oberdorfer Pumps

    Bronze Pedestal Gear Pump w/ relief valve

    N9000LRS15

    $794.00
    Bronze Pedestal Gear pump with relief valve. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the b...
  7. Oberdorfer Pumps

    Bronze Pedestal Gear Pump w/ relief valve

    N9000RE

    $1,044.00
    Bronze Pedestal Gear pump with relief valve. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by...
  8. Oberdorfer Pumps

    Bronze Pedestal Gear Pump w/ relief valve

    N9000RES17

    $1,068.00
    Bronze Pedestal Gear pump with relief valve. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the b...
  9. Oberdorfer Pumps

    Bronze Pedestal Gear Pump w/ relief valve

    N9000RS18

    $1,314.00
    Bronze Pedestal Gear pump with relief valve. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the b...
  10. Oberdorfer Pumps

    Bronze Pedestal Gear Pump w/ relief valve

    N9000RS3

    $1,044.00
    Bronze Pedestal Gear pump with relief valve. Often used as a oil pump on large ships to pre-lube the bearings.
    • Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the b...
View as List Grid

Items 21-30 of 31

Set Descending Direction
per page