My Cart

N Oberdorfer Gear Pumps Bronze

Oberdorfer Bronze Gear pumps Pump housings and gears are made of top quality bronze, shafts are from stainless steel 303. Bearings are designed of high performance carbon-graphite material selected for wear resistance and long service life.

Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of l9iquid relatively unaffected by the back pressure in the discharge line. Shaft speed and flow are directly proportional. Recommended pressure limits are 100 psi for water and non-lubricants, 150 psi for oil and lubricants. Maximum shaft speed is 1750 rpm.

A relief valve is necessary in the system if the discharge line contains any throttling devices, such as a shut-off valve, a spray nozzle or other restrictive device. This will return the liquid to the suction side or to the tank. The relief valve is also available as part of the pump itself (R-model pumps). However, built-in relief valves are only good for intermittent service. A built-in relief valve is strictly a safety device against overpressure. It will not work successfully as a pressure or flow control device. For this purpose a separate relief valve in the pressure line must be used.

Service life will be increase substantially if the liquid pumped is clean and has a lubricity value. These pumps have extremely close tolerances. Fine abrasives like sand, silt, or powder in suspension will destroy pumping ability.

Liquids compatible with bronze, stainless steel and the acrylic graphite packing can be pumped. Solvent resistant packings and Teflon® packings are also available.

Temperature extremes are detrimental to service life and should be avoided. Basic metals of construction allow temperature range of _40F to 400F. The acrylic graphite packing is rated to 500F. Freezing liquid in the pump can deform or damage the pump.

Viscous liquids such as molasses or oils require a lower pumping speed, in extreme cases as low ass 200 R.P.M. Liquids with specific gravities heavier than water such as dry cleaning fluids require an increase in motor horsepower directly proportional to the increase in specific gravity over water.

A rotary gear pump is capable of lifting water on the suction side as high as 20 feet. Though gear pumps are self-priming, a foot valve is recommended. For pumping water directly from streams or ponds, a wire mesh strainer must be used at the beginning of the suction line to prevent stones from entering the pump. Strainer and foot valve are commercially available as combination units.

NOTE: For the individual pump performance curves and dimensional drawings, please select a model from below. Used for vegetable oil, biodiesel.

Shop By
Shopping Options
Phase (Ø)
  1. Single (1) 11 items
  2. Three (3) 1 item
Voltage (Range)
  1. 110-120 3 items
  2. 220-240/460-480 1 item
  3. 110-120/220-240 8 items
  4. 12/24/36 VDC 2 items
Horse Power (HP)
  1. 1/4 1 item
  2. 1/3 3 items
  3. 1/2 6 items
  4. 3/4 2 items
  5. 1 3 items
  6. 1 1/2 1 item
  7. 2 1 item
inlet size
  1. Less than 1" 19 items
  2. 1 ¼" 2 items
  3. 1 ½" 2 items
PRICE $
$  -  $
Motor
  1. ODP 11 items
  2. TEFC 1 item
  3. TENV 4 items
View as List Grid

Items 11-20 of 31

Set Descending Direction
per page
  1. Oberdorfer Pumps

    N993 Pump & motor

    N993RM-J07

    $1,238.00
    Pump housings and gears are made of top quality bronze; shafts are from stainless steel 303. Bearings are designed of high performance carbon-graphite material selected for wear resistance and long service life.

    Gear pumps are positive displac...

    1/2HP 115/230v Relief Vavle Learn More
  2. Oberdorfer Pumps

    N993 bronze Gear pump

    N993R

    $784.00
    Pump Only PEO, no motor.Pump housings and gears are made of top quality bronze; shafts are from stainless steel 303. Bearings are designed of high performance carbon-graphite material selected for wear resistance and long service life.

    Gear pu...

    Pump Only PEO Relief Learn More
  3. Oberdorfer Pumps

    N991 Bronze gear pump PEO

    N991R-32

    $459.00
    Bronze gear pump & motor. 1/4" Pump housings and gears are made of top quality bronze; shafts are from stainless steel 303. Include relief valve built in. Bearings are designed of high performance carbon-graphite material selected for wear resist...
  4. Oberdorfer Pumps

    1.5" Bronze gear pump

    N13HDM

    $2,540.00
    1.5" Bronze rotary gear pump without relief valve. Pedestal mount pump only. Upper drive shaft location. See performance graph for flow rates vs motor RPM and HP. If used above 900 RPM, then duty cycle is limited to intermittent.
  5. Oberdorfer Pumps

    1.25" Bronze gear pump

    N11500-21

    $1,642.00
    1 1/4" Bronze rotary gear pump without relief valve. Pedestal mount pump only. Upper drive shaft location. See performance graph for flow rates vs motor RPM and HP (under image tab) . If used above 900 RPM, then duty cycle is limited to intermitt...
    Up to 55GPM Learn More
  6. Oberdorfer Pumps

    1.25" Bronze gear pump

    N11500S5

    $1,748.00
    1 1/4" Bronze rotary gear pump without relief valve. Pedestal mount pump only. Upper drive shaft location. See performance graph for flow rates vs motor RPM and HP (under image tab) . If used above 900 RPM with non-lubricating fluid, then duty ...
    Up to 55GPM FKM Lip seal Learn More
  7. Oberdorfer Pumps

    1.5" Bronze gear pump

    N13500-21

    $1,886.00
    1 1/4" Bronze rotary gear pump without relief valve. Pedestal mount pump only. Upper drive shaft location. See performance graph for flow rates vs motor RPM and HP (under image tab) . If used above 900 RPM, then duty cycle is limited to intermi...
    Up to 80GPM Learn More
  8. Oberdorfer Pumps

    Bronze gear pump

    N993Q-J46

    $1,749.00
    Pump housings and gears are made of top quality bronze; shafts are from stainless steel 303. Bearings are designed of high performance carbon-graphite material selected for wear resistance and long service life.

    Gear pumps are positive displac...

    1/2HP 115/230v Learn More
  9. Oberdorfer Pumps

    Bronze Gear pump For Hydraulic Motor

    N993S5

    $612.00
    Pump end only, no motor. Pump housings and gears are made of top quality bronze; shafts are from stainless steel 303. Bearings are designed of high performance carbon-graphite material selected for wear resistance and long service life.

    Gear pump...

  10. Oberdorfer Pumps

    Bronze gear pump Pedestal

    N3000RS15

    $1,044.00
    Bronze rotary gear pump with relief valve. Pedestal mounted bronze gear pump.

    See performance chart for HP required VS. motor RPM and pump performance.

View as List Grid

Items 11-20 of 31

Set Descending Direction
per page