Gear Pump & 12VDC Motor
-
Manufacturer:
-
Series (13 Models):
-
Product Name:Gear Pump & 12VDC Motor
-
Model Number:N992Q-01F94
Oberdorfer N992Q-01F94
Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the backpressure in the discharge line. Shaft speed and flow are directly proportional. Recommended pressure limits are 100 psi for water and non-lubricants, 150 psi for oil and lubricants. Maximum shaft speed is 1750 rpm.
A relief valve is necessary in the system if the discharge line contains any throttling devices, such as a shut-off valve, a spray nozzle or other restrictive device. This will return the liquid to the suction side or to the tank. The relief valve is also available as part of the pump itself (R-model pumps). However, built-in relief valves are only good for intermittent service. A built-in relief valve is strictly a safety device against overpressure. It will not work successfully as a pressure or flow control device. For this purpose a separate relief valve in the pressure line must be used.
Service life will be increase substantially if the liquid pumped is clean and has a lubricity value. These pumps have extremely close tolerances.
DC motors feature Permanent Magnet Rigid Base Motors, made by Leeson in the USA. Compact DC portable units convenient for on site servicing of vehicles, machinery and field equipment. For pumping oil direct from crankcase or oil reservoir, drums, containers, transfer diesel fuel to vehicles, pumping other liquids and chemicals compatible with materials of construction. Basic metals of construction allow temperature range of -40ï½° to 250ï½°F.
Model Number | N992Q-01F94 |
---|---|
part number | N992Q-01F94 |
Series | N992 Gear Pumps |
Max Flow (GPM.) | 4 |
Max Flow GPH | 240 |
TDH Maximum (Ft) | 231 |
TDH Maximum (PSI) | 100 |
Horse Power (HP) | 1/3 |
Horsepower (IE .5, 1, 1.5, 20) | 0.3300 |
Inlet Connection Type | FNPT |
Inlet (In.) | 0.38 |
Outlet Connection Type | FNPT |
Outlet (In.) | 0.38 |
Wetted Materials | 304SS, Bronze |
Elastomers / O-ring | Buna-Nitrile |
Voltage (V) | 12DC |
Voltage (Range) | 12/24/36 VDC |
Motor | TENV |
Speed (RPM.) | 1725 |
Self Priming | Yes |
Suction Lift (FT.) | 20 |
Max Operating Temperature (F) | 140 |
Viscosity | Glycerine 880.00 cp 5000.00 ssu |
Shaft | 304SS |
Length (In.) | 14.250000 |
Mechanical Seal | LIP SEAL |
Mechanical Seal Type | Single |
Motor Bearings | Ball |
Coupling | Y |
Other | As a general rule, the suction lift should be kept at an absolute minimum by placing the pump as close to the liquid source as possible. A gear pump in new condition can lift 20 feet of water in the suction line. A foot valve (preferably with built-in strainer) is recommended at the beginning of the suction line. For a first start-up, the pump should be primed to avoid dry running. Minimum size of the suction pipe is the size of the pump inlet port. For longer suction lines (over 3 feet) or for viscous liquids, the pipe should be at least one size or two sizes larger than the pump inlet port. |
Pump Bearing | Carbon |
Impeller Material | Bronze |
Cord Length (Ft.) | 0 |
Duty | Continuous |
Drain | No |
Port Rotation | Yes |
Country of Manufacture | United States |
Weight (Lbs) | 45.000000 |
Warranty (YRS.) | 1 |